CATEGORIES

You are here: REFLOW OVEN > Benchtop Reflow Oven

All Products In Category:   T962A | T962 | T962C

Auto Infrared IC Heater Reflow Oven T962A

Quick Overview
Max 300×320 mm soldering area

INFRARED IC HEATER T-962A works automatically by micro-computer control. We adopt fast infrared radiation for heating and circular-wind to do temperature equalization, so the temperature in the drawer is very accurately and equilibrium. It is easy to use and the whole soldering process will be done automatically. It can satisfy dissimilarity soldering-request of SMD、BGA and can soldering the most smart small part. It also can do two-side soldering for the PCB board. The faintness controlling technique and viualization-drawer workbench, make the whole soldering process completed at your observation. The highly dependable design, make you gratified and reassurance when using it. The device is powered by standard 110VAC 50/60HZ (220VAC Model is available).

Auto Infrared IC Heater Reflow Oven T962A Features

The T962A is a self-contained Micro-Processor controlled IC Heater and solder rework station.

Uses up to 1500 watts of energy efficient Infrared heating and air circulation to re-flow solder in a large 300×320mm area.

Parameters of Eight (8) Soldering cycles are Pre-Defined.

Soldering cycles are keypad selected and progress displayed on the T962A LCD.

A single windowed drawer holds assemblies within the heating chamber

The T962A design is ergonomic, practical and easily operated.

The T962A is an economical rework solution from single runs to on-demand small batch production.

Light weight and a small footprint allows the T962A to be easily bench positioned transported or stored.

The T962A can solder most bosseyed or double-face PCB boards' small parts, ie.: CHIP、SOP、PLCC、QFP、BGA etc; Can be

    used to the gum of the product solid, turning the circuit board hot aging, maintaining the PCB board and so on. Be satisfied to the

    needs of "academe", "smallorder run" and "extensively development of enterprise & company".

Auto Infrared IC Heater Reflow Oven T962A Specification

Model: T-962A

Soldering max area: 300×320mm

Rated power: 1500W

Process period: 1~8min

Temperature Range: 100℃-350℃

Supply voltage: AC110V/50~60Hz or 220V/50~60Hz

Size: 430×370×260mm

Picking size: 500×430×330mm

Net weight: 13.5KG

Gross weight; 15.5KG

Auto Infrared IC Heater Reflow Oven T962A Description

INFRARED IC HEATER T-962A works automatically by micro-computer control. We adopt fast infrared radiation for heating and circular-

wind to do temperature equalization, so the temperature in the drawer is very accurately and equilibrium. It is easy to use and the whole

soldering process will be done automatically. It can satisfy dissimilarity soldering-request of SMD、BGA and can soldering the most smart

small part. It also can do two-side soldering for the PCB board. The faintness controlling technique and viualization-drawer workbench, make the whole soldering process completed at your observation. The highly dependable design, make you gratified and reassurance when using it. The device is powered by standard 110VAC 50/60HZ (220VAC Model is available).


User interface is implemented by way of T962A input keys and an LCD display. Pre-Set heating Modes are selected by user interaction with thermal cycle progress observed on LCD display. The T962A may be used to automatically "re-flow" solder to correct bad solder joints,

remove/replace bad components and complete small engineering models or prototypes. A windowed drawer is designed to hold the work-

piece. Thermal cycle accuracy is maintained by closed loop micro-computer control with infrared heaters, thermocouple and circulating air.


(1) Big cubage soldering area

Soldering max area of T-962A is 300×320mm.


(2) Many choices of temperature wave

There are eight kinds of temperature parameter waves provided for you to choose, you also can operate the machine with HM-Heating.And

there is cooling fan with the machine. Whole soldering process will be complete automatically. It's very easy to operate.

 

(3) Special heat up and temperature equalization with all design

Output the power reaches to 1500W(T-962A), fast infrared radiation combined with wind-circulation, make the temperature in the drawer

more exact and equality. Whole soldering process to be completed automatically according to temperature parameter waves you choose.


(4) Humanized science and technology exquisite article

Firm of external appearance, operation with visualization, hail-fellow operation interface, the perfect temperature wave project, from start to

eventually display that the science and technology is the root. The light weight and small cubage will save more money for you, the desk-top placed, can also save more space for you. The simple operating instructions, make you use the machine easily.


(5) Perfect function choice

With the function "return soldering, drying, heat preservation, cooling quickly" on the machine.It can soldering the most smart small part,

as CHIP、SOP、PLCC、QFP、BGA etc; It can used to turn the product gum-solid, the circuit board is hot aging, the PCB plank maintains

and various works. It will be satisfied to each kind of business enterprise, company extensively develop and the small quantity demand of

production.

Auto Infrared IC Heater Reflow Oven T962A Description

1.Place the T962A on an appropriate level, insulated work area.
2.Make Sure the work space is well ventilated (exhaust fans may be necessary).
3.Allow at least 20mm between the T962A and its surroundings for heat protection.
4.Confirm the Work drawer opens and closes smoothly and without obstruction.
5.Locate supplied universal power cord and connect same from rear apron to AC power.
6.Locate and press the power on button, the LCD will light, the T962A will log on.

 

Press “s” button, the main menu will appear on LCD.

1.jpg

Press “F4” to Select English Menu

2.jpg

In the main menu

Press “F3” button selection different temperature wave. Example select wave1

3.jpg

Press “F3” button again, can see parameter about you choose the temperature wave:  

Select: soldering paste sort, soldering temperature, time etc. example:

9.jpg

When selections are complete, then Press “F4” button to return previous page. Press the temperature wave that the”F1” key

carries out to make selection automatically.

When it is ending, the work will shut down automatically, and the warning buzzer is working.

In the main menu page, press “ F2”button by handcraft operation

5.png

Press “F1” button to start cooling, Press F1/S key again to stop. Press “F2” button to start heat up, Press F2/S key again to stop.

Wave Cycle Select:

1.Press the “S” button to select operational interface after switch on, press the “F4” to select a different language category.

6.jpg

2.Following we provide eight different waves, please choose one according to your request. Press the F1/F2 to choose different

wave, press F3 to look into different wave parameter, press 4 to confirm the wave you chose:

Wave one, use the same with 85Sn/15Pb 70 Sn/30Pb

Wave two, use the same with 63Sn/37Pb 60 Sn/40Pb

Wave three, use the same with Sn/Ag3.5; Sn/Cu 75 Sn/Ag4.0/Cu.5

Wave four, use the same with Sn/Ag2.5/Cu.8/Sb.5; Sn/Bi3.0/Ag3.0

Wave five, use the same with The red gum standard is solid to turn temperature wave,Heraeus PD955M.

Wave six & seven & eight, use the same with The PCB circuit board returns to fix etc.

Wave seven & eight, use the same with the wave cycle set-up by yourself.

4.jpg
Press “s” button to the temperature page.
6357851404942591644327956.jpg

Press F1/F2 button, ahead/ backwards select different time. Press F3/F4 button ,up/down to select different temperature,

Press “s” button to save.

8.jpg

When save finish, press “F4” button to select the temperature wave. Press “S” button to repetition.

 

Operating instructions:
1.
Lightly puts the product which will be processed in the drawer of the oven on the stage , Close drawer, Press F1 to switch on,

    the automatic performance make selection of heat wave, Show current performance time, the enactment temperature and

    temperature on the LCD screen, and automatically note the formed wave of the temperature.

2. The whole process is in your supervision, you may see it by the window of the drawer, and you may see the data from the

    LCD screen. If the wave doesn't achieve your request, please modify the data by yourself.

3. The pre-set up wave cycle is according to the temperature that the different solder paste needs. You can pre-set up other wave

    cycle according to your needs.

4. In the process, you can press "S" to force to stop; When finished, the exhaust fan will work automatically to cool, you also can

    force to turn on the exhaust fan.

5. Complete the soldering, if somewhere is faulty, you can sold it automatically again, or you can sold it manual.

 

Operation Suggestions:

1. To satisfy the need of soldering both sides of the PCB, there is a particular designed fan duct in the machine. When the both

    sides of the PCB are of large difference in temperature, it can sold the patch in one side, and in the same time, it can keep

    another side of the PCB as well. To satisfy the soldering of the small board, please pre-put a PCB board in the size of 10cm*10cm,

    when soldering the small board and the solder-ball. It will make the soldering effect very well.

2. When use the machine, please pre-heat it if the environment is of low temperature, too humidity. The method: after choosing the

    wave cycle, run the machine with nothing in the drawer at the first time.

3. Attention: The machine can't be used to soldering the chips( the chips which with metal encapsulation are of strong glisten),and

    the "plastic plug in board" which can't be able to bear the temperature of 250 degree centigrade.

4. About the method to measure the temperature of the machine: Use the standard weatherglass. Fix the probe on the face of the

    PCB board(make sure it is the face ),then put the PCB board into the drawer, close the drawer. And then you will get the actual  

    temperature.

 

Maintenance:

a. Keep the inside of the machine clear. Please do as follows:
    When used the machine several times, please turn on the "heat-up" and the "exhaust fan" two or three minutes handly, to make the

    flux remained in the machine volatilization. It will keep the inside of the machine cleanness, and make the function of the machine

    stabilization.
b. Clean the drawer observation glass as necessary.

 

Warning !
1. Make sure the power supply is connect with earth.
2. Do not turn off the switch at once after using, make sure the machine is cooling, and then turnn off the switch and cut the power supply.
3. There isn't any way to do smoke evacuation, please put the machine in a ventilated condition to avoid poisoning

    (when the solder paste volatilization).
4. The insulations in the machine had been treated strictly. Do not take apart the machine until there is any safe protection.

Auto Infrared IC Heater Reflow Oven T962A Package

Model: 1 X Main Body (T-962A)

1 X Fuse (10A)

1 X Power Line (We stock 110V-240V power version and US.UK.EU.AU. plugs for the country all over the world.)

1 X User Manual

Inquiry in Auto Infrared IC Heater Reflow Oven T962A
×
Product Auto Infrared IC Heater Reflow Oven T962A
Name
E-mail
Country
Phone
Other
Inquiry